AGMA Gear Handbook Gear Classification, Materials and Measuring Methods for Bevel, Hypoid CNCL S/S BY AGMA * CONTAINS FOLDOUT. Buy AGMA A (R) Handbook – Gear Classification, Materials And Measuring Methods For Bevel, Hypoid, Fine Pitch Wormgearing And Racks . Jan 12, Buy AGMA GEAR CLASSIFICATION, MATERIALS AND MEASURING METHODS FOR UNASSEMBLED GEARS from SAI.
|Published (Last):||18 March 2009|
|PDF File Size:||14.91 Mb|
|ePub File Size:||12.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is because the present measurement capabilities 390.0 uncertainty values too large to allow for the proper statistical analysis of accuracy grade B3. Accuracy grades B3 through B10 7. Download Now Artificial intelligence Agma Bias choices are typically made from experience and, whenever possible, with data from actual loaded testing of the bevel gear set.
An accurate method is essential for calibrating the dial indicator or recording equipment over the working range; — Other considerations: In this standard, lower AGMA accuracy grades designate higher precision in order to be consistent with international standards.
Out–of–roundness may be caused by errors in machine tools, cutting tools, lack of rigidity in setup, hardness variation in the gear blank or heat treat distortion. See annex B for typical tooth contact patterns and examples.
Are you an Engineering professional? The top of a gear 390.033 is the upper portion of the tooth surface. Practices and measurement methods are included which are recognized and accepted throughout the gear industry as being reliable. Therefore, little or no final inspection may be necessary for a gear, particularly in some classification levels; assurance of the necessary accuracy having been built–in through careful manufacturing control at each step.
Bevel gear CMM measurements are commonly applied to assist with applications to the manufacturing process. If a recorder is employed, it is desirable to have a definite relationship between the position on the chart and a circumferential position on either the work gear or reference gear. This characteristic is commonly specified by the gear engineer to assure that the bevel tooth mesh will have proper action under loaded conditions.
This yields the true position pitch, pm.
Such curves are a graphic representation of some of the types of non–uniform motion that gears are likely to transmit. The CMM must be calibrated by a certified and approved method and must have a suitable environment. Tooth thickness by caliper Typical measuring method Minimum number of measurements Two probe Single probe Two probe Single probe Ball probe Single probe–index Double flank composite action CMM special software All teeth All teeth All teeth All teeth All teeth All teeth All teeth 3 teeth approximately equally spaced Roll test machine Double flank tester Single flank tester All teeth All teeth All teeth Tooth caliper 2 teeth approximately equally spaced 3 teeth approximately equally spaced 3 teeth approximately equally spaced TM: These are then output in a graphical or numerical format.
Manual interpretation can be done by drawing in the upper and lower envelope of the measured data. Definitions and allowable values of deviations for corresponding flanks of gear teeth 7. Annex material provides guidance on specifying an accuracy grade and information on additional methods of gear inspection.
The spur and helical portions of AGMA By either choice, advanced mathematical techniques are required to define this shape.
Item Detail – AGMA
This test also includes the effects of tooth–element variations. To achieve a legible tape transfer pattern record, first be certain the pinion and gear teeth are free of oil or other foreign material.
If the document is revised or amended, you will be notified by email. Join your peers on the Internet’s largest technical engineering professional community.
The functional backlash is dependent on the tolerances on tooth thickness, runout, tooth geometry and mounting distance. In the previous classification system AGMA For other The terminology and symbols used in this standard are amga alphabetically by term in table 1, and alphabetically by symbol in table 2.
Applicable definitions are provided. These tables are calculated from the equations in 7.
The toe of a bevel gear tooth is the agam of the tooth surface at the inner end. After much study and discussion, the classification system in this standard was agreed upon.
At the time of publication, the editions indicated were valid. Proper control begins with good organization. In general, these tolerances cover the following ranges: Retain the photographs in an organized fashion to allow future reference. Download Now Over the past This force needs to be uniform over the entire reading scale. The following standards contain provisions which, through reference in this text, constitute provisions of this American National Standard.
For the same quality of tooth form and runout, the tooth–to–tooth variation will be greater for a gear with a lower number 390.30 teeth than it will for higher numbers of teeth.
The inspection of gearing mated in an assembly for a specific application is ama the scope of this standard. The system of classifying very accurate gears with a low number, instead of retaining the method of AGMA Measurement requirements are to be agreed upon by the manufacturer and purchaser. It must be certified by complete measurement.