L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Tugar Kazshura
Country: Algeria
Language: English (Spanish)
Genre: History
Published (Last): 3 April 2004
Pages: 455
PDF File Size: 7.39 Mb
ePub File Size: 3.19 Mb
ISBN: 957-1-56362-336-5
Downloads: 42027
Price: Free* [*Free Regsitration Required]
Uploader: Dolkis

Originally approved in Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The steels shall adhere a666 specified chemical composition requirements. Historical Version s – view previous versions of standard. Material Test Report and Certi? It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and x666.

Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? D PSS means plate, strip, sheet.

The values given in parentheses are for information only. Number astmm Tests 8. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Link to Active This link will always route to the current Active version of the standard. This revision of Speci?

A — 03 Standard Speci? Hard Elongation in 2 in.

Only annealed conditions of grades speci? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. C Annealed material that naturally meets mechanical properties may be applied. The noncontrolling factor normally will exceed considerably the speci?

  DIN 66165 PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. However, in the case of dispute, tests shall be made by pressure. Rockwell B 95 95 The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

The values given in parentheses are for information only. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Last previous edition approved in as A — This abstract is a brief summary of the referenced standard. One bend test shall be made from one end of each coil. Current edition approved Oct.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?


ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

HardC Elongation in 2 in. This standard has been approved for use by agencies of the Department of Defense. In case of dispute, the offset method of determining yield strength shall be used.

They shall be formed in asfm shapes such as sheets, strips, plates and flat bars.

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. This specification covers austenitic stainless atsm in the annealed and normally required cold-worked conditions.

An alternative method of determining? B Maximum unless otherwise indicated. A number in parentheses indicates the year of last reapproval. ICS Number Code