Bentley AutoPLANT Piping XM Edition is an object-based 3D piping design and modeling The software enables users to interactively route and place piping. 3d Modeling enhances Quality. AutoPLANT Piping V8i provides 3D modeling capabilities through ObjectARX technology, using 3D objects to represent. Bentley AutoPLANT Piping XM Edition is an object-based 3D piping design and modeling application that runs on AutoCAD. . PDMS Piping Tutorial. Uploaded .

Author: Samura Zulkizilkree
Country: Laos
Language: English (Spanish)
Genre: Medical
Published (Last): 7 January 2018
Pages: 165
PDF File Size: 13.85 Mb
ePub File Size: 18.15 Mb
ISBN: 686-1-46258-507-9
Downloads: 30601
Price: Free* [*Free Regsitration Required]
Uploader: Arashinos

These can be created in the Project Setup step, but sometimes this can be forgotten or push back until the first model is loaded. In the example above, the valve is currently selected in the session and the other components are also going to be dismantled. Below is an image of this to help in locating it.

How does Configuration Editor relate to Briefcase Mode? There are a number of different ways to use Centerline. These points decide how the nozzles will be aligned. Centerline Routers are tools to place intelligent centerlines that can be used to place components. Just select the desired direction and press Enter when done.

Before one begins to model, there are a few things that they should be aware of. Document Manager is a document management tool that is included with AutoPLANT, while Vision has more features and has it’s own license that has to be purchased. After selecting this, the below dialog will appear – This dialog allows users to Load or unload the selected module or all of the modules.

Zoom to Selection Zoom to Line Allows for quick zooming to components, either by the selection or line number. Some of the messages given by the Consistency Report are not as clear, as one can see below – In image, the message says “Status: Topworks and Supports can even be included in the Assembly, or even make up the whole Assembly. Here is what they do – Insert – inserts the component into the drawing with the set changes and sets the status to Rebuilt Delete – deletes the component from the line and sets the status to Deleted Restore – removed the component from the list without making any changes Another section to know about is the Insertion Mode.

When placing an Equipment Primitive, the program will start out by requesting the Tag number for this Equipment. Advanced Tap Port Method Most of the time, a component that requires a Tap Port can be placed with the basic tap port placement. The program will go through a number tutorkal these options to determine what is best needed for this particular placement of the Assembly.


Laying out the placement of pipe can take the largest amount of time in a project. The Spec and Size columns can be changed by selecting them.

Some of Vision’s features include Report generating and list of Tags with their corresponding runs and models. From there, click the Create to begin the creation process. This will first request a Tag for the new Equipment, we will call this one ST Autiplant this example, I am going to change the Size for this from 6, which is what the original components were that made up this assembly, and I will use 4 instead.

In this image the ball valve is anchored, notice how the centers of the 4 in the light blue and the center of the 6 in the gray are in the same location – If the anchor is turned off on this component, here is the results – Notice that center of the Rebuilt valve is offset from augoplant center of the original one.

What AutoPipe does is route pipe between existing components, such as the flanges and elbows in this example.

When starting a Tutoriwl Router, the program will first request the preferences that will be used for this line, unless using “From Dialog” which will ask if Router Line Info should be turned on or not. This is the best way to determine how it reacts. To begin working with these, one needs to start with an Equipment Primitive. Some of the properties can be modified, but that ahtoplant for more advanced users and I would not recommend doing it until the help file has been fully reviewed and not in a production environment until all the needed values have been pipint.

For example, the spool below could be used in multiple locations of a plant were a return with tuorial valve insert would be needed – If this spool is going to be used multiple times, we can make it into an Assembly so that it doesn’t need to be drafted every time. Select the line that needs to be changed. As one can see, the status stats that the component has not yet been inserted.


This dialog is displayed because the program needs some input on were the center of autoplanf bend will be placed. Select the LB flange and press OK to continue. CS — MENU Allows users to quickly select a component from a spec record and place it Settings for the component are determined by what is in Component preferences.

The first step in the creation process is to select all the components that will make up the Assembly. It also allows the user to view information about each module so that they can learn more about it.

Basic Modeling in AutoPLANT

After all the dialogs have been processed, the program will then request the insertion point to be selected. After running AutoPipe, the line should be component and look like this. Auth with social network: If this spool is going to be used multiple times, we can make it into an Assembly so that it doesn’t need to be drafted every time. This is the tool that allows users to configure and customize the way Configurations work, similar to how Project Administrator allows the customization of Projects.

When the application is loaded, it will go straight into the model and begin to load the associated application. Tutoriak components must be lined up so that their centerlines are the same. Here, the drafter will need to give the document a name and select the application to associate the document to. Once this is done, all the selected components will change their size to 4 like below.

What is Assembly Manager? Published by Jeffrey Baker Modified over 3 years ago. Next, the program will request that you pick a point for the elevation. This is helpful for when the user needs tutofial work on the model when they don’t have access to the project. This dialog allows users to Load or unload the selected module or all of the modules.

AutoPLANT Piping – Tips and Tricks – ppt video online download

To load a module, just select the module from the Available Modules list, pick the desired option, and then hit either OK or Apply. This radio button has two choices, Auto Insert and Prompt.

My presentations Profile Feedback Log out.