Dome Camera Installation Manual Weatherproof and Indoor versions www. Contents Introduction. Menu System Manual. Page 4 of 1. THE DENNARD TYPE DOME CAMERA. The Dennard Dome Camera is a precision unit, offering a wide. The Dedicated Micros Camera has a number of features which can be selected by the System. Supervisor when the dome is installed. Any of these can be.

Author: JoJonris Mazugrel
Country: Gambia
Language: English (Spanish)
Genre: Marketing
Published (Last): 28 October 2009
Pages: 417
PDF File Size: 4.76 Mb
ePub File Size: 2.42 Mb
ISBN: 324-1-44292-325-8
Downloads: 44779
Price: Free* [*Free Regsitration Required]
Uploader: Mezibar

For example using the 36x optical zoom on a standard UK car number plate can be viewed at full screen width up to 17m away from the camera versus 11m away with 18x camera, or 13m away 26x. Attach bond to a suitable secure position in the ceiling void. Hanwha Techwin introduces four stainless-steel dome cameras to Wisenet X series. Patrol mode 260 cancelled with any manual dennarrd action. Tile Mounting – Weatherproof Dome mm mm Attach the mounting disc A to the dome in the chosen position and use 3 of the existing M4 dome hd screws to attach the hemisphere to denjard dome.

This product is marked with the CE symbol and indicates compliance with all applicable directives. Remove and retain the four screws securing the shield to the head and lift off the shield.

Dennard Dedicated Micros 2060 D PTZ Dome Camera CCTV

The bracket casting can be oriented to position the cable entry hole below, on either side of at the top. From above, clamp to the tile via 2 x off split clamp rings C.

Ceiling installation is dennarr easier by removing an adjacent ceiling tile during installation. Radiated Emissions Standard, suitable for Commercial or Residential use. Finally secure the plastic cover to the metal pins on the bracket flange C.

The desired protocol and the node address for the dome are selected by the two rotary hex switches blue and yellow inside the dome. Software Version The single letter in the middle of the reference indicates the supported camera, refer to the table below for more information.


The location of the switches is also shown. Troubleshooting No joystick dead band recognized as joystick was off centre during powerup. Picture with intermittent control Cause 1. When reassembling the dome, check the hemisphere sealing gasket is in dennatd and that the hemisphere retaining screws are retightened to avoid water ingress. Reset the Dome software reset Open the Technician Menu see Operation and Programming manual for details on accessing the menu.

Advanced privacy patches, preset positions and tour facilities. The installer is responsible for ensuring the fixings used to mount the dome are suitable for the material and will adequately support the weight of the dome. Locate SW3 on the main PCB adjacent to the mounted connector attaching the daughter board housing the yellow and blue address switches. Open the Technician Menu refer to the Operation and Programming manual for details on accessing the menus.

Ceiling Mounting – Weatherproof Dome Attach the mounting disc B to the ceiling in the chosen position and fix 4x M6x16 socket head cap screws supplied dennare the bushes C as shown below. US Edition International Edition. Scan across the table to identify the values for the blue and yellow switches.


You need to be a member in order to leave a comment. Dennadr the DVR is set to use the correct telemetry protocol and address settings.

Secure the mounting disc with 4 x supplied off M6 socket button head fixings D. I believe that the setup 260 UTC when previously installed so would have thought that the camera protocols would be set already. Re-install the tile in the ceiling. By ramformerApril 3, in General Digital Discussion. The weight of dome should be supported by bond ensuring no stress is placed on centre connector at any time. Table of Contents Add to my manuals Add.


The switch settings for the protocols and node addresses are shown in the table below.

Dennard 2060 PTZ Speed Dome Camera 36 x Optical Zoom with Swan Neck (Fully re-furbished)

Use a spirit bubble level against one of the flats to align accurately. The weight of dome should be supported by bond ensuring no stress is placed on centre connector at any time. Dedicated Micros Dennard P. Attach the mounting ring to the dome using the provided 6 x M3x8 fixings C. Looking for our US Edition?

Fit the cavity plugs A to the holes. Check the continuity on the power and video cables. Open the Technician Menu see Operation and Programming manual for details on accessing the menu. dennard

Always support dome with bond prior to mating connector. Operating Temp o C: Mounting brackets may have been ordered and delivered separately.

This operation should be carried out in an office type environment to avoid ingress of dennnard air. Check the dome address switches are correctly set for the controller being used.

Arecont Vision Contera indoor dome series. Camera Version To verify the version of camera supported by the dome software; 1.

Dennard Dedicated Micros D PTZ Dome Camera CCTV | eBay

Always support dome with bond prior to mating connector B. Software Version To check the version of software installed in the dome; 1. Control Switches – Indoor Dome Clip safety bond to 200 mounting bracket eyelet A on flange of bracket to secure.

Control Switches – Weatherproof Dome The location of the switches is also shown. Twist once located to secure, then tighten screw heads C to secure the dome enclosure to the mounting disk. The switches are factory set to FD DM up the coax control.