Find great deals for Haas Sl CNC Lathe. Shop with confidence on eBay!. Large selection of second-hand Haas SL available here. Great offers from top traders & auctions all in one place. Buy your Haas SL today!. Productivity Inc – Haas CNC Lathe Operator Manual. Page 1. Haas Lathe Operator Training Manual. Table of Haas VMC (SL) showing the X and Z axis.
|Published (Last):||13 March 2004|
|PDF File Size:||9.84 Mb|
|ePub File Size:||18.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
CALM System All solenoids located in the lube panel Use needle tipped probes and take care not to touch probes tips together when checking voltage. The lathe has a 12 tool station turret with an X standard axis. Mercuriusstraat 28 B Zaventem, Belgium Phone: The HAAS turning diameter is millimetres. A failed o-ring will also allow for coolant and chip intrusion into the back side of the turret.
Most big websites do this too. TC Turret Haws 2 4. The net weight of the sl10 HAAS is kilograms. If the o-ring under the rear turret chip skirt fails it can cause binding and prevent the turret from rotating has position.
Remove the upper hose unclamp on the cylinder. Haas World Europe China International.
The Haas Resource Center
Newsletter Subscribe to our newsletter. TC Turret Hqas If there is movement in the turret the die springs are broken and need to be replaced.
Go to Video Gallery. Remove lock out tags, power up and zero return the machine.
The voltage should measure VAC. If the cables are not damaged then the sensor will need to be replaced.
Haas SL – 6. If there is no voltage, refer to: Info-mailer for “Haas SL” By entering and confirming your email address, you will receive an e-mail notification as soon as new offers are received for your search. To make this site work properly, we sometimes place small data files called cookies on your device.
Air Cylinder Assembly Please click the link in the email we just sent you, to complete the subscription process. In MDI command an M43 and press cycle start to unclamp the turret. The servo motor has an electrical fault. Axis rotating slowly, hesitating to rotate. Servo Motor Back to Top. Turret Clamp Sensor Watch the diagnostics screen to ls10 sure they activate with the magnet. Select by Model Type Indexers. You have successfully subscribed. Haaas the turret is knocked out of alignment you may have wl10 re-align the turret motor coupler.
Possible failed motor, bad or contaminated cable connection, a damaged cable, or failed amplifier. In this case the turret should be removed to clear the chips and inspected for possible damage. We value your feedback. Male Turret Coupling Please fill in a valid e-mail address! Use a magnet and pass it over the sensors.
Female Turret Coupling Actual product appearance may differ. Average price Result is based on all current available offers for this product. Use needle tipped probes and take care not to touch probes tips together when checking voltage. In this case the turret should be removed to clear the chips and inspect for possible damage.
Recently Updated Last updated: Belleville Washers 2 Cookies To make this site work properly, we sometimes place small data files called cookies on your device. Select by Model Type Chucker Lathe. To confirm your subscription, click the link, we’ve sent you by mail.
Turret Indexer Assembly – SL/30 ST/15 – Troubleshooting Guide
Hass Indexer Assembly 2. TC Switch Ring Contact Haas Haas Europe Headquarters: Lathe – Turret Motor Coupling – Alignment. Turret Die Springs 7. The HAAS company is the biggest machine tool builder in the western world and has an international reputation for high levels of accuracy in its lathes. Make sure a minimum 1″ 25 mm space is between the turret and all objects in the direction of the Z Axis. It comes haax with a 12 tool-station turret, hydraulic chuck, Toolsetter, chip conveyor, parts catcher, rigid tapping, tool holders and bar feed interface.